FXR Fwd/Rev ESC 12 Turn Limit
The FX series leads the industry in brushed competition performance. With its ultra-small footprint and flash-programmable microcontrollers with the lowest on-resistance MOSFETS ever used in a speed controller, the FX completely eliminates any power bottleneck between your battery and motor, increasing efficiency and breathing new life into your brushed motors. The FX has thousands of possible settings right on-board with Tekin's QuickTune? Programming and is also capable of extensive tuning and updates when used with Tekin's HotWire PC Interface (sold separately).
The FX-R reversing speed controller leads the industry in pure rock crawling performance. With its tiny footprint, improved drag brake resolution with lock-down holding power, adjustable reverse type with reverse delay, no reverse or instant reverse, ultra smooth low speed creep and precision throttle and braking response, the FX-R easily gives you the edge over the competition. The FX-R has thousands of possible settings right on-board with Tekin's QuickTune? Programming and is capable of extensive tuning and updating when used with Tekin's HotWire PC Interface*. The FX-R can also take on your power needs with 3S Li-Po compatibility when used with 35 turn or higher motors. Install the FX-R and step up to smarter, smaller, faster electronics. And if you have an older FX-R you can download the latest software updates with our HotWire interface.
Input Voltage: 2S-3S LiPo / 4-9S NiMH-NiCD
BEC: 6.0v @ 3amps **External BEC needed for 3S applications**
Motor Limit 2S: 12T Brushed 540
Motor Limit 3S: 35T Brushed 540 Crawler
Throttle Profiles: 7 choices on board
Reverse Type: None / Immediate / Delay
Reverse Strength: 11 steps on board
Drag Brake: 11 steps on board
Brushed Modes: FWD Only / FWD-REV / FWD-REV Delay
Dimensions: 1.1 x 0.80 x 0.40" / 28 x 20 x 10mm
Weight: 0.63oz / 18g
- Ultra-smooth and Precise Throttle and Braking Control
- Easily Access Programming, Anywhere, Anytime
- HotWire PC Interface for Advanced Programming and Updating
- On-Board Temperature Indicator
- HDAC: High Density Copper PCB's
- Gold-plated Solder Posts for Easy Wire Replacement
- Self Test Diagnostics and Factory Reset
- Pit Tune Mode
- DGF2: Digital Glitch Filtering V2
- QuickTune? Programming
- One-Touch Radio Calibration
Tekin's Pro Hand Wound Brushed Crawler Motors are raising the bar with the release of the 30 and 40 turn versions. Perfect for all aspects of rock crawling, these Pro Hand Wound motors give you the punch or the creep when and where you need it. whether crawling the rocks or hopping over them, the lower turns give an increase in wheel speed many are looking for in today's setups. Using the same larger comm, lay-down brushes and precision balanced hand winds as our previous trail-proven pro motors, the Tekin Pro Hand Wound T- Series motors are ready to get the job done. Pair a Pro motor with the FX-R speed control and harness the professional brushed power!
The HD "Heavy Duty" T-Series brushed motors, available in the same 35, 45 and 55 turn options as before with an upgraded ferrite magnet to get you wherever you want to go with authority. New looks, better performance and the same great Tekin quality you know and trust! Designed to be paired with the FX-R speed control.
Input Voltage: 2S-4S LiPo / 4-12S NiMH-NiCD
Weight: 171g / 6.03oz
Shaft Dimensions: 3.2mm (1/8") x 11.3mm
Motor Diameter: 35.8mm / 1.41"
Motor Length: 52.5mm / 2.10"
Magnet Material: FB12 Ferrite (HD) / FB9 Ferrite (Pro)
- Brushed Motor Design
- Dual precision Ball Bearings
- Alloy Endbell Heat Sink Plates
- Gold Plated Copper Solder Tabs and Brush Hoods
- Hand Wound Armature (Pro model)
- Adjustable Timing
- High Torque Specification
- High Strength Ferrite Magnets
- Completely Rebuildable
- Legal in Rock Crawling Competitions
- Your choice of 35, 45 and 55 turn, Heavy Duty or Pro Hand Wound